John deere sx75 manual download.John Deere Manual

Looking for:

John Deere RX63, RX73, RX75, SX75, RX95, SX95 Technical Manual TM PDF 

Click here to DOWNLOAD

     

John deere sx75 manual download -

 

Essential tools required in performing certain service work are identified in this manual and are recommended for use. Live with safety: Read the safety messages in the introduction of this manual and the cautions presented throughout the text of the manual.

This is the safety-alert symbol. When you see this symbol on the machine or in this manual, be alert to the potential for personal injury.

Technical manuals are divided in two parts: repair and diagnostics. Repair sections tell how to repair the components. Diagnostic sections help you identify the majority of routine failures quickly.

Information is organized in groups for the various components requiring service instruction. At the beginning of each group are summary listings of all applicable essential tools, service equipment and tools, other materials needed to do the job, service parts kits, specifications, wear tolerances, and torque values. FOS Manuals are for training new personnel and for reference by experienced technicians. Technical Manuals are concise guides for specific machines. Technical manuals are on-the-job guides containing only the vital information needed for diagnosis, analysis, testing, and repair.

Component Technical Manuals are concise service guides for specific components. Component technical manuals are written as stand-alone manuals covering multiple machine applications. Please discard old TM dated February For complete engine repair information use CTM Engine tests and adjustments are covered in Section of this manual.

Model RX63 has been added. An abundance of diagnostic information has been added to the operation and test sections. All information, illustrations and specifications in this manual are based on the latest information available at the time of publication.

The right is reserved to make changes at any time without notice. Group 05—Safety. Other Material. When you see this symbol on your machine or in this manual, be alert to the potential for personal injury.

Handle fuel with care: it is highly flammable. Do not refuel the machine while smoking or when near open flame or sparks. Always stop engine before refueling machine. Fill fuel tank outdoors. Prevent fires by keeping machine clean of accumulated trash, grease, and debris. Always clean up spilled fuel.

Wear close fitting clothing and safety equipment appropriate to the job. Prolonged exposure to loud noise can cause impairment or loss of hearing. Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises.

Keep area clean and dry. Never lubricate or service machine while it is moving. Keep hands, feet, and clothing from power-driven parts. Disengage all power and operate controls to relieve pressure. Lower equipment to the ground. Stop the engine. Remove the key. Allow machine to cool. Securely support any machine elements that must be raised for service work. Keep all parts in good condition and properly installed. Fix damage immediately. Replace worn or broken parts. Remove any buildup of grease, oil, or debris.

Disconnect battery ground cable - before making adjustments on electrical systems or welding on machine. Escaping fluid under pressure can penetrate the skin causing serious injury. Avoid the hazard by relieving pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Search for leaks with a piece of cardboard. Protect hands and body from high pressure fluids.

If an accident occurs, see a doctor immediately. Any fluid injected into the skin must be surgically removed within a few hours or gangrene may result. Inspect boss O-ring boss seat. It must be free of dirt and defects. If repeated leaks occur, inspect for defects with a magnifying glass. Some raised defects can be removed with a slip stone. Occasionally a lower durometer O-ring will seat against a rough seat.

If neither of these solutions work, the component must be replaced. Put hydraulic oil, petroleum jelly or soap on the O-ring.

Put a thimble over the threads to protect O-ring from nicks. Slide O-ring over the thimble and into the turned down section of fitting. For angle fittings, loosen special nut and push special washer against threads so O-ring can be installed into the turned down section of fitting. Turn fitting into the boss by hand until special washer or washer face straight fitting contacts boss face and O-ring is squeezed into its seat. To position angle fittings, turn the fitting counterclockwise a maximum of one turn.

Tighten straight fittings to torque valve shown on chart. For angle fittings, tighten the special nut to valve shown in the chart while holding body of fitting with a wrench. To be used if a torque wrench cannot be used. After tightening fitting by hand, put a mark on nut or boss; then tighten special nut or straight fitting the number of flats shown.

For complete specifications on repair of Kawasaki engines see CTM Engine sheave mounting cap screw torque. Engine mounting cap screw torque. Spark plug gap. Spark plug torque. Idle mixture screw initial setting 6 hp. Idle speed. Wide open throttle no load. Fuel pump output at rpm Cover cap screw torque.

Shift lever detent set screw torque. Flush with cover Brake lever nut torque. Tie rod attaching nut torque. Brake pedal free play. Brake pad thickness min. Mower spindle sheave locknut torque. This manual is part of a total product support program. TM 17APR90 T Follow recommended precautions and safe operating practices.

TS Wear a suitable hearing protective device such as earmuffs or earplugs to protect against objectionable or uncomfortable loud noises. X Search for leaks with a piece of cardboard. Published on Aug 18, John deere sx75 riding mower service repair manual Published on Aug 18, Go explore.